Crack tutorial: Make your 1.1.1iPhone spend version 1.1.2! !

Can finally spend version 1.1.2 iPhone, we no longer need to be reduced to 1.02 or 1.1.1 1.1.2 iPhone using the ~ ~
The following tutorial release ~

Preparations:

Check your version to really be able to properly break:
Download, unzip, and then use it to spread to the next WINSCP usr / bin, click the button to enter the HOM COMMAND window, enter chmod + x bbupdater and press Enter, then enter the following command

launchctl remove com.apple.CommCenter
bbupdater-v

The results obtained are as follows:
Resetting target ...
pinging the baseband ...
issuing + xgendata ...
firmware: DEV_ICE_MODEM_04.01.13_G
eep version: EEP_VERSION: 207
eep revision: EEP_REVISION: 8
bootloader: BOOTLOADER_VERSION: 3.9_M3S2

If the return value is above tips, congratulations, you can use 100% 1.1.2, if not, it may succeed, but not guaranteed. The following tutorial is only for the above tips do.

Required Software:
iPhone firmware 1.1.1
iPhone firmware 1.1.2
anySIM1.2.1u
iPHUC
iTunes 7.5
Java Runtime Environment (JRE) v1.6 (update 3)
WinSCP
1.1.2 Jailbreak

An upgrade to 1.1.2
step1: Connect your iPhone with iTunes, iTunes prompts new software 1.1.2 update, click to download and update, then you can disconnect the iPhone data cable, allowing iTunes to download the software, shut down iTunes, and then make the following operation;

step2: re-open iTunes, even on the iPhone, then press HOME + POWER button when the phone is black screen, release the POWER button, but based upon the HOME button until iTunes prompts to find a prompt recovery in the state, and then release the HOME key;

step3: Turn off the prompt box, hold down the SHIFT key on your computer, and then "restore" button is clicked on iTunes, then will pop up a file selection window, double-click you just downloaded iPhone1, 1_1.1.2_3B48b_Restore (the file in the C : \ Documents and Settings \ youname \ Application Data \ Apple Computer \ iTunes \ iPhone Software Updates in), then start the upgrade to iPhone 1.1.2;

step4: After the upgrade is complete, iPhone will automatically reboot and enter the active interface, to this end we upgrade your modem firmware will become 04.02.13_G.

Two back again 1.1.1

step1: Before downgrading, we first have to install the Java Runtime Environment (JRE) v1.6 (update 3), so that your computer can use the JAVA program (jar program.);

step2: the iPhone connected to the computer, and open iTunes. Then press the HOME + POWER button when the phone is black screen, release the POWER button, but based upon the HOME button until iTunes prompts to find a prompt recovery in the state, and then release the HOME key;

step3: Turn off the prompt box, hold down the SHIFT key on your computer, and then "Restore" button will pop up a file selection window, double-click the previously downloaded iPhone1 on iTunes, 1_1.1.1_3A109a_Restore (the file in the C : \ Documents and Settings \ youname \ Application Data \ Apple Computer \ iTunes \ iPhone Software Updates in), then the iPhone began to downgrade to 1.1.1;

step4: When the "recovery" is completed, you will get a prompt for the 1015 error, do not be afraid, then we use jailbreak1.1.2, and double windows batch file will pop up a dialog box as shown below:


We click on "Boot from Recovery", probably need only 2-5 minutes, you can see the interface to be activated;

step5:. sliding interface "emergencydialscreen", enter the emergency call screen

Enter the "* # 307 #" in an emergency dial screen, then press the green "Call" button. (As you call)

Your phone will start ringing Do not answer. Cancel "* # 307 #" then press enter "0", your iPhone will automatically ringing, press the "call" button.

Your phone will ring, and now press "Answer" to answer, press the "hold".

Your phone will ring again, now press the "decline".

Press the "decline" after the iPhone's menu will enter the non-locked state.

Click "Contacts" icon to enter the address book

Make sure you have a wifi and can access the Internet

You are now entering the address book, the point right corner of the screen "+" to add contacts.
In this contact where you need to add two web addresses.
The first address input: prefs :/ / 1F
The second address input: http://jailbreakme.com

Click on the first address, will enter the setting interface, select a wifi network and set the autolock never

And then return to Earth interface, and then enter the above methods address book, click on the second address just entered, the browser will pop up, but the browser will crash within seconds and return to Earth again after 3-5 minutes interface iphone will automatic restart, then activates a good
1.1.1
Third, under 1.1.1 crack
with anySIM1.2.1
step1: When activated, we install BSD Subsystem and OpenSSH
with Installer
step2: After setting WIFI, use winscp will anySIM.app copied to the Applications folder, then into the anySIM.app folder and open winscp command window, type chmod + x anySIM Enter

step3: Restart your iPhone, run anySIM, until the embankment is shown Successfully unlocked message, then described the successful break;

step4: Restart your iPhone, run the Installer again and install Tweaks OktoPrep (1.1.1) under;

Four, then upgrade back to 1.1.2

step1: the iPhone is connected to your computer, open iTunes, click on the "Update" button, remember clicking update, rather than click restore! !

step2: After updating, re-use jailbreak1.1.2, this time we have to choose to install "install SSH" and you can change the initial password, set up well by JailBreak;


step3: Then the screen shown below, the whole process take about 5-10 minutes, we can go to a WC or a drink of water;



Six successful break! !

When it's all over, you will see your iPhone already have a cell phone signal, and showed China mobile!!!
Reply:
Strong ... from the top ...
Reply:
Did not seem so simple, huh.
Reply:
Oh, a little more difficult